KYOCERA FS-680 Manuel d'utilisateur Page 131
- Page / 141
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
RS-232C Cable Connection
C-14
RS-232C Cable Connection
Preparing an RS-232C Cable
After obtaining an RS-232C cable, check that it is wired correctly, referring to the pin assignment table
in
Appendix C
. If you have an IBM communication adapter cable type 1502067, you will have to
resolder the wiring at the printer end of the cable. The procedure is as follows.
1. Unscrew the plastic cover from the printer end of the cable.
2. Next to each of the wires inside the cable is a bare shield wire. Solder all these shield wires
together into a single bundle.
3. Using a section of flat wire about 3 mm wide and 15 mm long, connect the bundle of shield wires
to the metal facing of the connector. Check that the solder connections are secure.
4. Desolder wires 2 and 3, then resolder them in crossed configuration. Solder wire 2 to pin 3 and
wire 3 to pin 2. Cover the solder joints with thermofit tube.
5. Cut wires 4, 5, 6, and 20.
6. Solder wires 5 and 6 together and connect them to pin 20. Cover the solder joints with thermofit
tube. Leave wire 4 unconnected.
7. Tape all remaining loose ends, or seal them with thermofit tube.
8. Screw the plastic cover back on.
- Users Manual 1
- Caution 2
- FCC statement 6
- Safety information 7
- Interface connectors 7
- CDRH regulations 9
- Ozone concentration 9
- Caution labels 9
- IMPORTANT SAFEGUARDS 10
- ISO 7779 10
- CE Marking Directive 11
- Introduction 12
- Safety & EMI Requirements 13
- Disclaimer 13
- KYOCERA ECO-PRODUCT 14
- Contents 18
- Chapter 1 20
- Installing the Page 20
- Power Supply 23
- Grounding 24
- Surrounding space 24
- Unpacking and Inspection 25
- List of packaged contents 26
- Moving the Printer 27
- Names of Parts 28
- Interior View 29
- Setup and Connections 30
- Top Cover 32
- Process Unit 32
- Protective Cover 32
- 4. Close the top cover 35
- 5. Add paper 36
- Close the cassette cover 38
- 39
- Parallel Interface Connector 40
- Option Interface Slot Cover 40
- Parallel Interface Connection 41
- 9. Attach the power cord 42
- 10. Test the printer 43
- Notes on Application Software 44
- Installing Under Windows3.1 48
- Click on Add >>. 49
- Printer. 49
- Expanding Memory 51
- Installing SIMM 53
- Screws 54
- Testing Extended Memory 58
- Chapter 2 59
- Operating the Page 59
- Control Panel 60
- Control Keys 62
- KIR Level 63
- KIR Setting Description 64
- Ecoprint mode 65
- Manual Paper Feeding 66
- Sub-Tray 67
- Feeding Envelopes 68
- Auto Manual Feeding 69
- Chapter 3 Fonts 71
- Bitmap and Scalable Fonts 72
- List of Fonts 73
- Resident Scalable Fonts (1) 74
- Resident Scalable Fonts (2) 75
- KPDL Fonts (1) 76
- KPDL Fonts (2) 77
- Chapter 4 78
- Maintenance 78
- Toner Container Replacement 79
- Chapter 4 Maintenance 80
- Replenishing Toner 81
- Toner Container Replacement 83
- Close the top cover 85
- Cleaning 86
- Chapter 5 89
- Troubleshooting 89
- General Guide 90
- Kyocera dealer 91
- Print Quality Problems 92
- (Continued on next page) 93
- Indicators Corrective Action 98
- Error Indications 99
- Correcting a Paper Jam 100
- Chapter 5 Troubleshooting 101
- Jam Inside the Printer 102
- Appendix A 104
- Printer Specifications 104
- Paper Selection 107
- Appendix B 107
- General Guidelines 108
- Paper Specifications 109
- Selecting the Right Paper 110
- Paper Size 111
- Smoothness 111
- Basis Weight 112
- Thickness 112
- Moisture Content 112
- Appendix B Paper Selection 113
- Special Paper 115
- Colored Paper 116
- Preprinted Paper 116
- Postcards 117
- Envelopes 117
- Appendix C 118
- Host Computer 118
- Interface 118
- Parallel Interface 119
- Interface Signals 120
- RS-232C interface 124
- RS-422A interface 126
- Overview of Signals (RS-422A) 127
- RS-232C/RS-422A Protocol 128
- PRESCRIBE FRPO D0 command 130
- RS-232C Cable Connection 131
- Appendix D 134
- Indicators 134
- Processing data 136
- Adding paper 136
- Selecting paper size 136
- Sleeping 136
- Manual feed 136
- Paper jam 137
- Top cover open 137
- Toner status 137
- Memory overflow 137
- Print Overrun 137
- Call-service person errors 138
Produits connexes et manuels pour Copieurs KYOCERA FS-680
Copieurs KYOCERA FS-3820N Manuel d'utilisateur
(227 pages)
(227 pages)
Copieurs KYOCERA KM-1810 Fiche technique
(4 pages)
(4 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.145 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels